JJRC JJPRO X1G-The carbon house princess

Discussion in 'New Products, News, Advancements, etc.' started by Soros Gyula, May 21, 2017.

  1. Soros Gyula

    Soros Gyula New Member

    JJRC JJPRO X1G-The carbon house princess

    Packing

    As always the drone arrive in box which made from cardboard. Inside packing is very well maked, because for quadcopter have a same for this reason cuted plastic small box upper in box which make possible to separate from other things and with them minimalize chance for damage. This is also true for there is

    The package including: A drone, Transmitter, Monitor with them an antenna and screen holder which could be assembled to transmitter, camera an

    Outside (Chcel by som sa tu pisat ze z zvonka ,ale kludne to oprav ked niekde som pouzival slova nespravne)

    The drone body as written maked from carbon, however when touching it remember to plastic which is afterworked, but after some of crashing could be decided its it real carbon or not. As we watch from upper we could found a GPS, but it’s only a cheap plastic and we could found some marks which is showing ahead

    Okay so lets dissamble...

    If we want to dissamble need to remove 16 screws from copter body. After these screws are removed, we could finally get to 2 piece. Inside we will motherboard in the middle with plugs and connected unknown receiver.

    Motors...

    As the motors we will get a JJRC brand ,which technical parametres is 2280 KV ,which as whole copter sold and "racing drone",which after testflight inside me get a feeling this technical parameter is not correct,because the reagating was not so fast as in situation with ZMR 250,however need to constate it to JJRC only 2S battery giving a juice ,for ZMR 250 3S as usual.

    Kamera and the FPV receiver.

    As from camera we will get a 720 p where sometimes experienced fish eye effect.The camera body is made from plastic which is strong.As holding in copter we will bet a straight forward cutted plastic,where need to push the camera after (ako zadrzenie dostane taky maly kolaj kde ked to uz cvakol bude drzat v poriadku). As

    As FPV receiver we will get a 8 CH modell, which is (vyhnut sa pred preplnenimi WIFI kanalom) ...and one button with which could these channels switched. For cooling is able to a small cooling board, which is enough combined with air cooling.

    Transmitter

    As transmitter we couldn’t need to expect to nothing special only for usual settings and usual buttons (360 degree eversion, levels of reagating etc...) and at back we will found 2 buttons which is only design and not reagating for nowhere...As assamble it is not so good, because the plastic transmitter body was crapping and t

    Monitor

    As monitor we will receive a 4,3 col with model. As settings we doesn’t get much, only languages (there is a lot from there 2 type Chinese ,English,France,German etc...),contract, brightness and we could manage the recorded photos and videos. Unfortunatly the battery was small (only 400 mAh and 3,7 V) with which it couldn’t be working more than 20 minutes. As design everything was okay, however an antenna plug will be

    Accesories which are part of box: Landing gear without them is difficult to landing, because the camera and the receiver, however a little bigger it recommend due to better protection. And the propeller protectors are still good, however in this copter that is unnessary, because it them wrong his effecient and simple could stuck at tree in moments.

    As the extra propeller we will get 8 pcs,4 pcs RED and 4 pcs BLACK, with which are trying to better show the ahead side. As material using we will get a stong plast, which after crash didn’t breaking to his atoms only deformate, but sometimes we could fly with damaged propeller, but it’s dangerous so fly with them caution. As size we will get a 5 inch propps, which are usually used in racer section.

    Test flying and sumarrum...

    To start the drone motors we need to the first control joystick stick move to left corner and holder there approx. 3 seconds,but of course after we connected drone with the transmitter, which we could do it with throttle joystick move up and down. After drone take off it so much stable, but without senzors like barometer, GPS always need to corrigate. The reagate levels in usable, as from easy, where




    As the drone is not as bad job ,however it could be better if there could a 3 cell battery and motors, only with few cm will be better in all side ,which is acceptable and it could be more powerful. As the drone material using I am not sure perfectly if his body made really from carbon not spoken as screw discounting in motor sections...(using only 3 however motor have 4 place for that...) As the motherboard problem I am trust its only sample error, not serial, however in previous model it was been comed too lot of time. As I want it it’s better plastic using as the transmitter body, bigger battery and antenna plug for the monitor.
     

Share This Page